Common error code definitions for error handling. More...

Macros
#define	ERR_ABORT 0x0200
	user aborted something

#define	ERR_ACCES 0x012D
	Permission denied.

#define	ERR_ADDRINUSE 0x014A
	Address already in use.

#define	ERR_ADDRNOTAVAIL 0x014B
	Can't assign requested address.

#define	ERR_AFNOSUPPORT 0x0149
	Address family not supported by. More...

#define	ERR_AGAIN 0x000B
	Try again later.

#define	ERR_ALREADY 0x0137
	Operation already in progress.

#define	ERR_APP 0x8000
	application specific errors start here

#define	ERR_BADF 0x0009
	Bad file handle.

#define	ERR_BUSY 0x0010
	Resource busy.

#define	ERR_CANO_CAL 0x0340
	CAN application layer error.

#define	ERR_CANO_CAL_NO_DEVICES 0x0341
	no devices detected on bus

#define	ERR_CANO_DEVPROF 0x0600
	device profile specific errors

#define	ERR_CANO_DLL 0x0300
	Data link layer error.

#define	ERR_CANO_DLL_ARBITRATION_LOST 0x030A
	arbitration lost - this is not really an error, its more an event

#define	ERR_CANO_DLL_BUS_OFF 0x0306
	CAN "bus off" error occurred.

#define	ERR_CANO_DLL_CAN_ERR 0x0309
	a CAN bit or frame error occurred

#define	ERR_CANO_DLL_CFG 0x0315
	Configuration of device failed or configuration not supported.

#define	ERR_CANO_DLL_ERR_PASSIVE 0x0305
	CAN "error passive" occurred.

#define	ERR_CANO_DLL_HW_NOT_AVAILABLE 0x0312
	if CAN hardware is detected but could not be used or initialized

#define	ERR_CANO_DLL_HW_NOT_FOUND 0x0311
	if CAN hardware could not be found - i.e. when detecting USB devices

#define	ERR_CANO_DLL_HWERR 0x0301
	hardware error of CAN controller

#define	ERR_CANO_DLL_HWSWERR 0x030E
	Function could not be performed because of hard- or software errors.

#define	ERR_CANO_DLL_OVERRUN_RX 0x0307
	overrun in RX queue or hardware occurred

#define	ERR_CANO_DLL_OVERRUN_TX 0x0308
	overrun in TX queue occurred

#define	ERR_CANO_DLL_PARA 0x0314
	Calling parameter(s) is (are) not correct or out of range.

#define	ERR_CANO_DLL_PHY_FAULT 0x030B
	General failure of physical layer detected (if supported by hardware)

#define	ERR_CANO_DLL_PHY_H_FAULT 0x030C
	Fault on CAN-H detected (Low Speed CAN)

#define	ERR_CANO_DLL_PHY_L_FAULT 0x030D
	Fault on CAN-L detected (Low Speed CAN)

#define	ERR_CANO_DLL_RES 0x030F
	Resource error - The resource limit exceeded at creation of a queue or something else.

#define	ERR_CANO_DLL_RXQUEUE_EMPTY 0x0316
	no message received because RX queue of controller is empty

#define	ERR_CANO_DLL_SUPP 0x0313
	function is not supported this way

#define	ERR_CANO_DLL_TX 0x0310
	A CAN message couldn't be sent for a long time - cable error, wrong baud rate etc.

#define	ERR_CANO_DLL_TXFULL 0x0302
	TX queue of CAN controller is full.

#define	ERR_CANO_DLL_WARNING_RX 0x0303
	TX error counter (TEC) reached warning level (>96)

#define	ERR_CANO_DLL_WARNING_TX 0x0304
	RX error counter (REC) reached warning level (>96)

#define	ERR_CANO_SDO 0x0400
	SDO transfer errors.

#define	ERR_CANO_SDO_ABORT 0x0401
	SDO transfer aborted.

#define	ERR_CANO_SDO_ABORT_BLOCK_SIZE 0x0405
	invalid block size in block mode

#define	ERR_CANO_SDO_ABORT_CMD 0x0404
	command specifier not valid or unknown

#define	ERR_CANO_SDO_ABORT_CRC 0x0407
	CRC error (block mode only)

#define	ERR_CANO_SDO_ABORT_DATA_DEV_STATE 0x041C
	data cannot be transfered or stored to application because of present device state

#define	ERR_CANO_SDO_ABORT_DATA_LOC_CTRL 0x041B
	data cannot be transfered or stored to application because of local control

#define	ERR_CANO_SDO_ABORT_DATA_LONG 0x0413
	data type does not match, length of service parameter too high

#define	ERR_CANO_SDO_ABORT_DATA_OD 0x041D
	object dictionary not present or dynamic generation fails

#define	ERR_CANO_SDO_ABORT_DATA_SHORT 0x0414
	data type does not match, length of service parameter too short

#define	ERR_CANO_SDO_ABORT_DATA_TRANSF 0x041A
	data cannot be transfered or stored to application

#define	ERR_CANO_SDO_ABORT_DEV_INCOMP 0x0410
	general internal incompatibility in device

#define	ERR_CANO_SDO_ABORT_GENERAL 0x0419
	general error

#define	ERR_CANO_SDO_ABORT_HW 0x0411
	access failed due to hardware error

#define	ERR_CANO_SDO_ABORT_MAN_SPECIFIC 0x04FF
	manufacturer specific error code

#define	ERR_CANO_SDO_ABORT_MAP_LEN 0x040E
	number and length of object to be mapped exceeds PDO length

#define	ERR_CANO_SDO_ABORT_NO_MAP 0x040D
	object cannot be mapped to the PDO

#define	ERR_CANO_SDO_ABORT_NOT_EXIST 0x040C
	Object does not exist.

#define	ERR_CANO_SDO_ABORT_OUT_OF_MEM 0x0408
	Out of memory.

#define	ERR_CANO_SDO_ABORT_PRAM_INCOMP 0x040F
	general parameter incompatibility reasons

#define	ERR_CANO_SDO_ABORT_READONLY 0x040B
	attempt to write a read only object

#define	ERR_CANO_SDO_ABORT_SEQ_NUM 0x0406
	invalid sequence number in block mode

#define	ERR_CANO_SDO_ABORT_SUB_UNKNOWN 0x0415
	sub index does not exist

#define	ERR_CANO_SDO_ABORT_TIMEOUT 0x0402
	SDO protocol timed out.

#define	ERR_CANO_SDO_ABORT_TOGGLE_BIT 0x0402
	toggle bit not altered

#define	ERR_CANO_SDO_ABORT_TYPE_MISMATCH 0x0412
	data type does not match, length of service parameter does not match

#define	ERR_CANO_SDO_ABORT_UNSUPPORTED 0x0409
	unsupported access to an object

#define	ERR_CANO_SDO_ABORT_VALUE_HIGH 0x0417
	value range of parameter written too high

#define	ERR_CANO_SDO_ABORT_VALUE_LOW 0x0418
	value range of parameter written too low

#define	ERR_CANO_SDO_ABORT_VALUE_RANGE 0x0416
	value range of parameter exceeded

#define	ERR_CANO_SDO_ABORT_WRITEONLY 0x040A
	attempt to read a write only object

#define	ERR_CONNABORTED 0x0161
	Software caused connection abort.

#define	ERR_CONNREFUSED 0x0169
	Connection refused.

#define	ERR_CONNRESET 0x0162
	Connection reset by peer.

#define	ERR_DEADLK 0x0023
	Resource deadlock would occur.

#define	ERR_DEADLOCK ERR_DEADLK

#define	ERR_DESTADDRREQ 0x0141
	Destination address required.

#define	ERR_DEVCFG 0x0204
	invalid device configuration

#define	ERR_DEVNOSUPP 0x00CA
	Device does not support this operatio.

#define	ERR_DEVSTATE 0x0205
	wrong device state for this operation

#define	ERR_DOM 0x0021
	Argument to math function outside valid domain.

#define	ERR_EOF 0x00C8
	End of file reached.

#define	ERR_ERROR 0x0202
	common unspecified error

#define	ERR_EXCEPTION 0x0203
	application has thrown an exception

#define	ERR_EXIST 0x012E
	File exists.

#define	ERR_FBIG 0x001B
	File too large.

#define	ERR_HOSTDOWN 0x016C
	Host is down.

#define	ERR_HOSTUNREACH 0x016D
	No route to host.

#define	ERR_INPROGRESS 0x0136
	Operation now in progress.

#define	ERR_INTR 0x0004
	Operation interrupted.

#define	ERR_INVAL 0x0016
	Invalid argument.

#define	ERR_IO 0x0005
	I/O error.

#define	ERR_ISCONN 0x0164
	Socket is already connected.

#define	ERR_ISDIR 0x0015
	Is a directory.

#define	ERR_LISTEMPTY 0x0206
	could not execute an operation because of an empty list

#define	ERR_MFILE 0x0018
	Too many open files.

#define	ERR_MSGSIZE 0x0142
	Message too long.

#define	ERR_NAMETOOLONG 0x003C
	File name too long.

#define	ERR_NETDOWN 0x015E
	Network is down.

#define	ERR_NETRESET 0x0160
	Network dropped connection on reset.

#define	ERR_NETUNREACH 0x015F
	Network is unreachable.

#define	ERR_NFILE 0x0017
	Too many open files in system.

#define	ERR_NOBUFS 0x0163
	No buffer space available.

#define	ERR_NODEV 0x0013
	No such device.

#define	ERR_NOENT 0x0002
	No such entity.

#define	ERR_NOERR 0x0000
	No error.

#define	ERR_NOMEM 0x000C
	Out of memory.

#define	ERR_NOPROTOOPT 0x0144
	Protocol not available.

#define	ERR_NOSPC 0x001C
	No space left on device.

#define	ERR_NOSUPP 0x00C9
	Operation not supported.

#define	ERR_NOSYS 0x0026
	Function not implemented.

#define	ERR_NOTCONN 0x0165
	Socket is not connected.

#define	ERR_NOTDIR 0x0014
	Not a directory.

#define	ERR_NOTEMPTY 0x0042
	Directory not empty.

#define	ERR_NOTSOCK 0x0140
	Socket operation on non-socket.

#define	ERR_NOTSUP 0x005F
	Not supported error.

#define	ERR_NOTTY 0x012F
	Inappropriate ioctl for device.

#define	ERR_NXIO 0x012C
	Device not configured.

#define	ERR_OPNOTSUPP 0x0147
	Operation not supported.

#define	ERR_PARAM_RANGE 0x0201
	value range of parameter exceeded

#define	ERR_PERM 0x0001
	Not permitted.

#define	ERR_PFNOSUPPORT 0x0148
	Protocol family not supported.

#define	ERR_PIPE 0x0130
	Broken pipe.

#define	ERR_PROTONOSUPPORT 0x0145
	Protocol not supported.

#define	ERR_PROTOTYPE 0x0143
	Protocol wrong type for socket.

#define	ERR_RANGE 0x0022
	Math result cannot be represented.

#define	ERR_ROFS 0x001E
	Read-only file system.

#define	ERR_SHUTDOWN 0x0166
	Can't send after socket shutdown.

#define	ERR_SOCKTNOSUPPORT 0x0146
	Socket type not supported.

#define	ERR_SPIPE 0x001D
	Illegal seek.

#define	ERR_SRCH 0x0003
	No such process.

#define	ERR_TIMEDOUT 0x0168
	Operation timed out.

#define	ERR_TOOMANYREFS 0x0167
	Too many references: can't splice.

#define	ERR_WOULDBLOCK ERR_AGAIN

#define	ERR_XDEV 0x0012
	Cross-device link.

Typedefs
typedef long	TErrCode
	This provides a common set of error codes that all packages can agree on. More...

Detailed Description

Common error code definitions for error handling.

Author: Uwe Kindler (UK)

Date: 2007/03/27

Typedef Documentation

typedef long TErrCode

This provides a common set of error codes that all packages can agree on.

It doesn't preclude them defining their own error return system, but this is a preferable system to use to help error support be as general as possible.

We try and conform to the ANSI/POSIX error code format, namely starting with the character 'E'. Error code type. A type for error codes which may be useful to explain the purpose of a variable or return code. It shows that it contains an error code of the type defined below

Macros

Typedefs

Detailed Description

Typedef Documentation